11/21/2022 0 Comments Vexilar d130 battery status indicator![]() If you have an Ultra pack, please go to the Vexilar web site for detailed mounting instructions. #Vexilar d130 battery status indicator proA piggy-back terminal has been provided for easy connection to the Genz or Pro Pack. Attach the red power lead from the FL Digital Depth Indicator to the positive terminal post of your battery. Take the other end of the DD-100 and plug it into the back of your Vexilar. Simply unplug your transducer from the back of your Vexilar and plug into the DD-100 connector. When not in use, the DD-100 goes to sleep, so you no longer have to worry about draining your battery when not in use. The DD-100 not only gives you digital depth, but also gives you the battery status by pressing a button. You can easily outfit your Pro Pack, Ultra Pack or Genz Pack with the DD-100. Designed to fit in place of the popular D-130 or T-130 battery indicators, Vexilar has been selling for years. #Vexilar d130 battery status indicator seriesNow you can easily and quickly attach the FL Digital Depth Indicator to your transducer cable from your FL series Flasher sonar and get an instant digital depth reading. The FL Digital Depth Indicator (model DD-100) gives anglers what they have been asking for, Digital Depth. Large amounts baitfish or huge schools of fish may also alter the actual depth read out.The FL Digital Depth Indicator is the first digital display to show depth at all times when your Vexilar flasher is on while still being able to get the status of your battery with the touch of the button. *Please note - Depth readings may not always be 100% due to variations of bottom content such as rock, sand, mud or weeds. Finally, place the DD-100 where the old battery indicator was and attach with either plastic push pins or use a small #6 bolt and lock nut. A "piggy-back" terminal has been provided for easy connection for the Genz or Pro Pack units. Attach the red power lead from the DD-100 to the positive terminal post of your battery. Installation: Simply unplug your transducer from the back of your Vexilar and plug into the DD-100 connector. Will not be able to do an air demo with it.Will not go shallower than 3 feet, but will read 3 feet regardless if it's even shallower.Works with all 12 volt batteries in conjunction with Vexilar flasher.It will not work in Low Power mode or with units equipped with s-cables (S-140 suppression cable) Digital Depth readings will not always be 100% accurate due to variable conditions.100%=12.7volts, 0%=11.0volts.Ī few other points to remember with the new DD-100. For example, if you push the "push to test button," and it reads 70%, that means your battery is at 12.2volts. The only time you will see a battery status is when you push the "push to test button." The battery status is given in percentages of voltage remaining in the battery. The DD-100 was designed to fit in place of the popular D-130 or T-130 battery indicators which Vexilar has been selling for years. Current draw: 124uA (micro amps) when off and 21mA (milliamps) when on. However, we still recommend that you disconnect your power when not in use for over long periods. When not in use, the indicator goes to "sleep," so you no longer have to worry about draining your battery when not in use. If your display is blinking or the depth numbers are going up or down rapidly, it could be that you're over a huge school of fish or baitfish OR the bottom is irregular. This will allow you to get your flasher in the best depth range possible. The digital depth portion of the indicator will work even if you're not in the correct depth range. The digital depth display will always give you a depth reading as long as your Vexilar FL flasher is turned on and the transducer is in the water. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |